Friday, November 26, 2010

Bedside table "slip-covers"

When we moved to our new house, my mom donated to us her old bedside tables since we didn't have any.  This is what they look like.... sad face...there's a matching one on the other side of the bed.I didn't leave them like that...I had a grey sheet tossed over each one which really wasn't much better.




After browsing through some new fun blogs, I came across a tutorial  from Ana White showing how to make a gorgeous, knife-pleated slip cover for a parson's chair.  I repeat....gorgeous.  And then it hit me,

I could make gorgeous little knife-pleated slip covers for my night tables!

Now as you may know...I have this habit of dreaming beautiful things...starting beautiful things....and then finding them semi-finished in the back of the closet three years later.   Not this project! I was determined to get'er done...and get'er done I did!

I had been eye'ing up this beautiful black idon'tknowwhat material at Fabricland on the upholstery/tabling/drapery shelf.  Low and behold, it was on sale when I came to get it! Wooooo sale!

A bunch of math, pinning, cutting and sewing later....this is how my first one turned out! Isn't she beautiful?! I gave the legs a lovely coat of silver spray paint to give them some class too!



EDIT: This picture is way better than the one I had up! Now you can actually see all my beautiful knife pleats!

 Here's a close up so you can see the gorgous material and the pleats I so carefully measured eye-balled....



Here's how I did it: (I didn't take too many pictures of the process 'cause the lighting in my house is lame so you'll just have to imagine as we go)

WRITE ALL OF THESE MEASUREMENTS DOWN SO YOU CAN REFER TO THEM LATER. 
This was the most complicated part - getting it all planned out.  Bear with me and feel free to ask if my directions make no sense!

1.  Measure the diameter of the tabletop and add 1 inch (1/2 inch seam allowance on either side)
2.  Measure the circumference of the tabletop and add 1 inch for seam allowances
3.  Measure how long you want the skirt of your cover to be, including pleat.
  • Decide how long you want the pleated section to be and subtract that from the total length of skirt.
4.  Take the length of skirt without pleat and add 1 inch for seam allowances
5.  Take the length of pleat and double it - add 1 inch for seam allowances

For example: My table stands 25 inches high.  The length of my finished skirt with pleat is 9 inches.  The finished pleat is 3 inches and the finished skirt is 6 inches. Therefore, my unfinished skirt measured 7 inches with seam allowance and my unfinished pleat also measured 7 inches with allowances (you fold this piece in half).

Once you've got all your measurements:

1.  Cut out a circle using the diameter of the tabletop plus 1 inch.
2.  Cut a long rectangle for the skirt.  The long edge should equal the measurement calculated in point 2 above (diameter multiplied by 3.14).  The short edge will be the length of skirt in point 4.
3.  For the knife pleat pieces, double the circumference length and add a foot or so (piece it together if need be...the seams won't show).  The length  should be twice your finished length plus 1 inch for seam allowances.

Mark all your pieces so you don't mistake skirt pieces for pleat pieces!

To make the pleat:

I referred to an awesome tutorial by Pink and Polka Dot on how to make knife pleats.  She lays it out really clearly.  I will emphasize one thing though. Do not underestimate the length of material you need. You will definitely need twice as much plus a foot.  I eyeballed my pleats as she did...I'm not that picky..or patient. 

To make the cover:

1. Pin your finished pleat to the skirt piece, right sides together and sew.
2. Iron seams up.
3. Match and pin the ends of your skirt/pleat together, right sides together and sew.  You should now have a complete circle.
4. Take your tabletop circle and pin to your skirting, right sides together. Use lots of pins and do an inch or so at a time keeping the edges lined up (this is not an exact science..) 
5. Sew!
6.  Put your finished cover on the table to make sure everything looks good.
7.  Fix it if it doesn't!
8.  Iron the seam down toward the skirt (use the narrow end of your ironing board for this)
9.  Put your pretty new table cover on and admire!!! (I ironed it again while it was on)

mmm buttonCatch As Catch Can

3 comments:

From Snowflakes To Hotcakes said...

Super cute!!! Well done! :-) Thanks for stopping by my blog today:-) I wrote a response to your comment over there, but I'll copy it here so you don't have to blog hop to find it. I don't know why the Thanksgivings are on different days, but I think I did at one point. (My college roommate was from Ottawa, and I'm pretty sure she told me.) For the life of me, I can't remember and I'm too stubborn to google it, because I know that I know... haha Anywho... I did Black Friday shopping once, but not this year. My family is doing handmade/homemade Christmas this year, so I don't need to go to most of the stores and the ones I would go to for stuff to make gifts are too far away to make it worth it. I guess you can get some good deals, but for me, shopping is torture on a good day. Add the Black Friday rudeness and craziness on top of it and I'd sort of rather stab myself in the hand with a fork. Well, maybe not that bad, but I'd definitely rather stay in bed. haha

Thanks for stopping over!

gail myrepurposedlife.net said...

huge transformation! You did a great job with the pleats. I'm supposed to being some box pleats on some chair slip covers. I detest sewing, so I keep putting it off. Well, that AND isntalling a new faucet. :)
thanks for linking up.
gail

Cammy said...

Don't be afraid of the pleats Gail! The finished product is always (usually) worth the blood sweat and tears. If not...banish it to the "unfinished projects" cupboard and start again...in 10 years when you have forgotten how bad the first try was!